SKU: 41346010011

SpeedyBee F405 Mini BLS 35A 20x20 Stack

$71.99 $79.99
Save 10%
No.2 Bestseller on mindclearing.info >

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 12 - Jul 17

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

SpeedyBee F405 Mini BLS 35A 20x20 Stack$59. 99 for a Bluetooth 35A Stack? Thats ridiculous! Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4 level battery voltage display, built in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs. 35A 4 in 1 BLHeliS Mini

$59.99 for a Bluetooth 35A Stack? That’s ridiculous!
Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
35A 4-in-1 BLHeliS Mini ESC: This ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.
Tune Flight controller and ESC wirelessly!
Power the quad, connect the SpeedyBee app via Bluetooth, configure the UART Ports,PID,OSD and every other settings on this flight controller. Also, every parameter of the BLHeli_S ESC in this stack can be set via the app.
With this Bluetooth stack, even micro drones become easy to tune—no need to worry about the hassle of inserting USB cables into the flight controller. Simply tune your drone wirelessly through the App, and say goodbye to wires and worries!
Powerful Real 35A 4-in-1 ESC!
6-layer 2oz PCB plus optimized circuit design equals stable and strong current output. The four-channel continuous 140A output can reach 30 seconds*.
The use of Japanese TDK filtering SMT capacitors and the onboard TVS protective diode, further enhances your flight experience, providing a seamless and reliable performance. The stack underwent rigorous pressure testing with various 5-inch freestyle and racing drones, confirming its powerful capability to effortlessly drive any 2-4 inch and lightweight 5-inch drones.
Clean Gyroscope Power Supply, Smoother Flight
Equipped with the renowned brand MaxLinear's LDO power supply chip, the gyroscope receives independent power, boosting surge protection capacity by 320%. Additionally, built with a 100uF ultra-large filtering tantalum capacitor, guarding the gyroscope's data from interference caused by the power source. Each posture and movement during flight receives precise responsiveness, allowing you to fully experience the pure beauty of flying!
Forgot your LiPo checker? Just look at the FC!
On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on goggles to check the battery status.
Change motor directions wirelessly!
Are you still using a computer to change motor directions? With this stack, when you finish your build, connect to the SpeedyBee app, change the motor directions just in a few simple steps*. Then take off.
* To use this feature, go to the App > Motors > Motor Direction Settings.
Support DJI Digital Video Transmitter
The flight controller has two independent 9V 3A BEC and 5V 2A BEC, supports various analog image transmissions above 5V, and also supports DJI O3 Air Unit/Link / Vista/Air Unit V1
M2 or M3? Why not both?
Have you ever experienced that the stack holes of your frame did not fit the stack you got? This stack is perfectly compatible with M2/M3 screws. What’s more, two sets of M2 and M3 screws + silicone grommets are included in the package!
TVS Protective Diode + 470uF Low-ESR Capacitor = Upgraded ESC Protection
The ESC is built with TVS protective diode to absorb the voltage spike when you plug in the battery, or during crashes that block your props. We also provide a Rubycon 470uF Low-ESR capacitor, ensuring clean data from the gyro to the FC.
And packaged with more useful features
● Sufficient 4 x UARTs for your receiver + VTX + camera + GPS.
● Two independent 5V 2A BEC and 9V 3A BEC.
● Power your GPS with a USB cable - no battery needed. No extra heat, no worries
● 17mm cutouts for FPV camera in your tight build
● Onboard barometer for real-time altitude sensing
● Onboard 8MB Blackbox storage
Specs Overview
Product Name SpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight Controller SpeedyBee F405 Mini
ESC SpeedyBee BLS 35A Mini V2 4-in-1 ESC
Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
WiFi NOT Supported
Wireless FC Firmware Flashing NOT Supported
Wireless Blackbox Dwonload & Analysis NOT Supported
Power Input 3-6S LiPo
Mounting 20 x 20mm 3.5mm hole size，Compatible with M2 and M3 screws/Silicone grommets
Dimension 32mm(L) x 35mm(W) x 14.2mm(H)
Weight 13.5g
Specifications
ProductName SpeedyBee F405 Mini Flight Controller
MCU STM32F405
IMU(Gyro) ICM42688P
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
Wireless FC Firmware Flashing NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update
Wireless Blackbox Dwonload & Analysis NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.
WIFI Not supported
DJI Air Unit Connection Way Direct soldering
DJI Air Unit Compatibility Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.
Blackbox 8MB Onboard Flash
BetaFlight Camera Control Pad Yes(CC pad on the front side)
Current Sensor Input Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.
5V Output 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output 1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 - M4 wires or soldering pads on bottom side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry UART R5(UART5)
I2C Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
RSSI Input Not Supported
Smart Port / F.Port Not Supported
Supported Flight Controller Firmware BetaFlight(Default), INAV
Firmware Target Name SPEEDYBEEF405MINI
Mounting 20 x 20mm 3.5mm hole diameter ，Compatible with M2 and M3 screws/Silicone grommets.
Dimension 30(L) x 32(W) x 7.8(H)mm
Weight 9.6g
ProductName SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
Firmware BLHeli_S J-H-40
Continuous Current 35A * 4
Burst Current 45A(5seconds)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT(Battery voltage, used to power the flight controller)
Current Sensor Support (Scale=250 Offset=-500)
ESC Telemetry Not supported
Mounting 20 x 20mm ∅3.5mm hole size，compatible with M2 and M3 screws/Silicone grommets.
Dimension 35 * 35 * 5.5mm
Weight 7.2g
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 41346010011

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 800 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
B
Verified Purchase
Billy
Boise, US
★★★★★ 4
Good speed
Color: C-Black, Size: Model C Rechargeable
Love the rechargeable feature, works great as a frother, however, I have to get use to the on/off feature instead of the press to froth like the older unit.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 22, 2026
L
Verified Purchase
Lady J
Carnegie, US
★★★★★ 5
Hold on tight! Has the strength to spin right out of your hands. 😀
Color: C-Stand Black, Size: Model C Rechargeable
What a pleasant surprise to experience this double whisk Electric Milk Frother!! The sheer power is incredible. Makes the most delicious blended Green Tea Match Latte, Dalgona Coffee and Mochas! The only "con" happened yesterday when I was frothing my Green Tea and the device just suddenly stopped! At the time, I wished that there was some sort of colored bulbs or other way of determining charge levels. A remarkably strong Milk Frother!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 7, 2026
M
Verified Purchase
Myriam I. Martinez
Belleville, US
★★★★★ 5
Good quality and durability
Color: C-Black, Size: Model C Rechargeable
It works very well very easy to use I'm very happy with my purchase
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 16, 2026
K
Verified Purchase
Kings Kidd
Lowell, US
★★★★★ 3
It froths, but is not dependent
Color: C-Black, Size: Model C Rechargeable
While this frother does “froth”, it has many more cons than pros. The ONLY pro is it froths. The cons—only good for a traditional coffee cup. It is not water proof, and the instructions say to keep the “unit “ dry. As you froth, the liquid naturally raises height. If you are trying to use a Togo coffee mug, or thermos type travel mug—it only works well if done it three or four levels to ensure keeping the motor above the liquid. The “rechargeable “ function DOES recharge, however- it may last 1use or a few. It’s VERY inconsistent. And does not seem to be related to how long you allow it to charge. Overall—not a good buy. I had mine maybe 3 months before it quit working. And at 2 months it started becoming spastic. Even after just being charged-it wouldn’t even froth 1cup. AVOID!!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 16, 2026
C
Verified Purchase
Carloslazaroproenza
Natrona Heights, US
★★★★★ 5
Easy to Use and Works Great
Color: C-Black, Size: Model C Rechargeable, Color: C-Black, Size: Model C Rechargeable
This milk frother works amazingly well! It’s powerful, easy to use, and creates rich, creamy foam in just seconds. The rechargeable design is very convenient, and the battery lasts a long time between charges. It feels sturdy and well-made, and cleaning it is quick and simple. I use it every day for my coffee, lattes, and hot chocolate, and it has exceeded my expectations. If you’re looking for an affordable and effective milk frother, this is definitely a great choice. Highly recommended
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 10, 2026

recommand products

Superlift 11-19 Chevy Silverado 2500HD Fox Shock Box - 1.5-3.5in Lift Kit Front/Rear Shocks
600.00
昇華バスケユニセット BK344
2705.00
Superlift 18-19 Jeep Wrangler JL 2/4 Door Superlift Shadow Shock Box - 2.5-4in Lift Kit
140.00
Clover Thread Snip "Kuroha"
36.99
Twister Sisters Twisty Zips Pattern **CLEARANCE**
13.99